A home appliance that works hardest for you is undoubtedly your refrigerator. Any problem with your refrigerator can negatively affect your daily routine. Therefore, it is important to keep your fridge in pristine condition. If you notice water droplets on refrigerator door, you should take steps to troubleshoot the problem with your residential appliance. If you ignore the problem, it can damage other parts of the machine. So, take steps to identify the cause of the problem and take appropriate steps to ensure the fridge repair service is a success. Before you call your refrigerator service technician, you should check the parts that could be responsible for the problem. Here are some parts that could be responsible for the problem. Door Gasket When the door seal is damaged, you will notice excess moisture on the shelves of the freezer or on the air outlet ducts. When the gasket is damaged, it can prevent the refrigerator door from closing properly. This will allow air to enter the machine and it may cause defrost issues. If you notice water droplets on the edge of the refrigerator door, it is an indication that gasket is not sealing properly and you must replace it. You can test this by putting a piece of paper at several points along the refrigerator door. Now, close the door normally and try to slide out the paper. If the paper slides out without any problem, it means the gasket is defective and it must be replaced. Door Assembly When the assembly is activated, it will dispense ice from the ice maker. The door assembly has a flapper that is spring loaded and has a rubber seal that prevents air from entering the household appliance. Sign of moisture near the dispenser or ice bin area is an indication that the door is not closed properly. To troubleshoot the problem, you must inspect the door assembly. To check the parts of the door assembly, you must remove the cover of the dispenser and inspect its operation. Some parts you must check include door seal, door hinges, and its pivotal mechanism. You must be able to open and close the door without any restriction or binding. If you find any defective part, replace it immediately. Door Closure Kit In side-by-side refrigerators, the closer cams assist in closing the refrigerator doors. The closer cams are made of nylon or plastic and they have shoulders that mate together. The door has two cams – one at the top of the door hinge and other on the bottom of the refrigerator door. If either of the closer cams is damaged, the refrigerator door will not close properly. This allows warm air to enter the machine and cause condensation. If the door is not closing properly, check the condition of the cams, and replace them if necessary. When replacing the cams, make sure you get genuine cams from a reputed store. Getting cheap unbranded cams will only damage the machine. The freezer and fresh food door rotate on hinges. These hinges act as bearing and allow the door to pivot on them easily. Regular use of hinges can make them dry. This can prevent the door from closing properly. Warm air can enter the machine from these gaps and cause moisture problems with the machine. A common symptom of a damaged or faulty bearing is when you hear a thumping or scraping noise when you close or open the door. Worn out hinges must be replaced immediately and make sure you lubricate them using a food safe grease. Lubricating the hinges will reduce friction and increase the durability of the hinges. If these steps don’t solve the problem, it is best to get help from a professional repairman. To carry out servicing or repairs, the technician will visit your home at your convenience. Before you call a professional, make sure you check the reviews given by customers who used their service. Also, make sure you get an estimate of total repair cost (including the cost of parts) before they carry out repairs. The quality of parts used by the technician has a direct impact on the durability of the machine. Therefore, make sure you check the warranty offer on the parts by the technician. Here Are Our Service Areas In These Popular Cities: Las Vegas, Little Rock, New Haven, Eugene, Tacoma, San Francisco CA, Phoenix, New York City, Middletown, Jacksonville, Everett, Boston, Tampa, Lakewood, Philadelphia, St. Louis, Cleveland, San Jose, Birmingham, Milwaukee, Oklahoma City, Allentown, Sacramento , Kansas City, Colorado Springs, Billings, Salt Lake City, Raleigh, Tallahassee, Albuquerque, Austin, Columbia, Provo, Baltimore, Nashville, Dallas, Denver, Seattle, Portland, Virginia Beach, Columbus, Orlando, Miami, Olympia, Los Angeles CA, San Antonio TX, Manchester, Tucson AZ, Minneapolis, Newark, Detroit, Richmond, Baton Rouge, Henderson, San Diego, Charlotte NC, Chicago, Silver Spring, Bowie, Aurora, Indianapolis, Providence, Reno City, Fort Worth, Jackson, Atlanta GA, Louisville, Pittsburgh, Portland, Omaha, Charleston SC, Houston The post How To Fix A Refrigerator Door That’s Sweating appeared first on OnSite Appliance
0 Comments
Not all home appliances are equally useful. We use some residential appliances almost every day, while we use other others occasionally. Appliances such as dishwasher, refrigerator, and washer, are some appliances that we use regularly. Any problem with these appliances can upset our daily routine. For instance, if your washer stops working, you may have to wash a pile of dirty clothes by hand, which is a tiring and time-consuming process. To troubleshoot the problem with your machine, it is best to get help from a repairman who is qualified and experienced in doing washing machine repair. If you feel that there is no major problem with your machine and you don’t require the services of a washer technician, you can try the washer repair yourself. However, make sure you take every possible precaution before you start working on your household appliance. One of the problems you are likely to encounter when using the washer is the timer not advancing. If you plan to troubleshoot the problem yourself, you should check the parts that could be responsible for this problem and repair or replace the damaged part. Some parts that can be responsible for this problem are: Lid Switch Most top loaders come with a safety feature known as the lid switch. This switch is usually located below the top lid of the washer. The switch has a pin or projection attached to it which activates the switch when the lid is closed. The switch supplies power to the motor circuits and the timer. Check if the lid switch is activated when the lid is closed. You must also visually inspect the condition of the actuators and levers and make sure they are not sticking or damaged. If the lid switch is activated but there is no power supply to the circuits and the motor, it means that the switch is damaged and must be replaced. To replace the switch, disconnect the power supply to the machine and remove all the wires that are connected to the switch. Once you remove the switch from the machine, check its condition using a multi-meter. Many people avoid replacing the lid switch that is broken or damaged. You should not do this as it is an important safety feature of the washer and can result in serious injury. Get help with this issue from qualified appliance repair professionals. Timer Motor Several functions of the washer are controlled by the timer. The timer has several electrical contacts that are operated by a motor or assembly. Some timer contacts control the functions of the timer motor. If the timer of the machine does not advance, it could be due to a problem with the motor or the timer itself. You can check the condition of the timer using a multi-meter. To do this you must have some knowledge of electrical schematics to determine the correct checks. If the timer is working properly, you must check the continuity of the time motor. If there is a problem with the timer motor, you may have to replace the timer assembly, as timer motor may not be available separately. Water Level Controller The controller is responsible for controlling the water valve of the washer. When the desired water level is reached, the controller turns off the valve which prevents water from overflowing. If the desired water level is reached but the machine timer does not advance, it may be due to a defective switch that controls the water level. You will need a multi-meter to check the condition of the switch. Before checking the condition of the water level switch, make sure you disconnect the power supply to the machine. Once you disconnect the power supply, remove all the wires that are connected to the switch. Now check the condition of each contact using a schematic diagram. Timer Knob The knob is attached to the machine’s timer shaft. This knob will turn as the timer advances through the wash cycle. The knob can also be used to activate the wash cycle by pulling out on a lever that activates the timer switch. This plastic knob has a metal insert that is attached to the timer shaft. Normal use of the washer can wear out the knob and prevent it from turning with the timer shaft. When the knob is damaged, it will be difficult for the timer to run to the desired wash cycle. Also, it will prevent the dial from turning with the shaft as the wash cycle advances. If you plan to replace the faulty dial or knob, make sure you remove the power supply to the house appliance. If power supply is not disconnected, you may inadvertently start the washer which can be a serious health hazard. To remove the timer knob from the machine, you may have to move it in and rotate it in an anti-clockwise direction. Some knobs are covered by cap and have a retaining clip that connects it to the dial. In these machines, you have to remove the cap and the retaining clip to remove the knob from the machine. Drain Pump The pump is responsible for removing the water from the tub at the end of the rinse and wash cycle. If there is a problem with the drain pump, the water will not drain from the tub and the washer will not advance to the next portion of the cycle. If you face this problem, you must check the condition of the drain pump. Some electronic washers display a fault code when the water does not drain from the tub. You can use this fault code to identify the exact cause of the problem. Water inlet Valve During the fill portion of the wash cycle, the inlet valve supplies both hot and cold water to the washer. The valve has two solenoids that are responsible for opening and closing the valve. If there is a problem during the spin cycle or if the machine stalls during the fill portion of wash or rinse cycle, it could be due to the faulty inlet valve. Before you check the condition of the inlet valve, make sure the inlet hose is not blocked or kinked. Also, make sure the inlet screen is clean. If there is no problem with the hose and screens, you can check the continuity of the solenoids using a multi-meter. This check must be done after you disconnect the power supply to the machine. If the solenoids test out OK, you must check the power supply to the solenoids. This washer service requires a live voltage check which should be performed by a trained appliance service technician. If there is no power supply to the solenoids, you must check the components of water level switch, time, lid and cycle selector switch. Check for the communities that we service in popular cities: Austin, Charleston SC, Tucson, Jacksonville FL, Orlando, Miami, Henderson, Charlotte, Indianapolis, San Jose, Richmond, Jackson, Chicago, Portland, Aurora, Olympia, Houston, Lakewood, Providence, Eugene, Manchester, Allentown, Salt Lake City, Cleveland, Everett, Fort Worth, San Francisco, Silver Spring, Detroit, Seattle, Pittsburgh, Philadelphia, Phoenix, Columbus, Oklahoma City, Dallas, Los Angeles, Atlanta, Tacoma, Baltimore, Boston, Provo, Sacramento, Louisville, Nashville, Baton Rouge, St. Louis, Raleigh, Portland, Austin, Colorado Springs, Kansas City, Albuquerque, Virginia Beach, New York City, Middletown, Milwaukee, Las Vegas, Billings, Tampa, New Haven, Tallahassee, Denver, San Diego, Little Rock, San Antonio, Birmingham, Reno City, Newark, Columbia, Omaha, Bowie, Minneapolis The post How to Fix A Washer That’s Timer Won’t Advance appeared first on OnSite Appliance When a house appliance is broken, it can disturb your normal routine. At times, the residential appliance may move or vibrate, which can make it difficult for you to use the appliance. For instance, you may not be able to wash your clothes when the washing machine moves or vibrates. You could get help of a washer technician to troubleshoot the problem. Alternatively, you could try to repair or service the household appliance without any professional help. Here are the steps you could take to identify and troubleshoot the problem with the washer.
Shock Absorber Most front-loading washers have shock absorbers that reduce the machine movement during the spin cycle. These shock absorbers are usually attached to the tub and the base frame of the machine. To assess the condition of this part, you must remove the rear or front panel of the machine. If you notice that the shock absorbers are damaged or broken, you must replace them immediately. If you don’t have the tools to replace the shocks, you can get help from a washer repairman. When the shock absorbers are damaged, they will unbalance the loads and cause the washer to move or shake. The home appliance will make loud banging sound when the washtub rotates. If steps are not taken to troubleshoot the problem, it can damage other components.
Tub and Suspension Spring Suspension springs of the washer are used either to stabilize the washer tub assembly to the base or to suspend the tub from the washer cabinet. These suspensions also absorb the vibrations of the washtub when the tub spins. When these springs are damaged, you can hear excessive noise from the home appliance during the spin cycle. To assess the condition of the suspension springs, you must remove the front or top outer panel of the washer. Visually inspect the springs and replace them, if necessary. Snubber Ring Some washers have a snubber ring that reduces vibration during the spin cycle. The ring is usually located at the bottom of the washer and it provides cushion to the tub support assembly and the washer base. When the ring wears out, it allows the washtub to move excessively, which can cause the washer to shake uncontrollably. To visually inspect the ring, you must remove the front panel. If you notice white dust on or near the ring, it indicates that the ring is worn out and must be replaced. To replace the ring, you must first remove the tub Tub Dampening Strap Some washers have straps that reduce vibration during the spin cycle. The straps are attached to the corner of the cabinet and top of the washtub. The straps are made of soft rubber that can wear out due to regular use. When the strap is worn out, the washtub can come in contact with the cabinet, which can cause the machine to shake. This can create loud banging sound. If the straps are damaged, you must replace all the straps at the same time. Changing the straps may not be easy, and it is in your interest to get help from a washer service Check Out The Popular Cities We Cover and Service: San Francisco CA dish washer repair, Little Rock, Orlando, New Haven dishwasher repair, Eugene, Tacoma, Jackson, dishwasher repair Phoenix, New York City dishwasher service, dishwasher service Middletown, Jacksonville dish washer service, Everett, Indianapolis, Tampa, Lakewood, dish washer repair Philadelphia, Atlanta GA appliance repair, St. Louis, Cleveland, appliance repair San Jose, Birmingham, Milwaukee, Portland, Oklahoma City, Allentown, Sacramento dishwashing machine repair, Kansas City, Colorado Springs, Billings, Salt Lake City, Raleigh, Tallahassee, San Antonio TX dishwasher service, Albuquerque, Austin, Columbia, Provo, Baltimore, Nashville, Dallas, Denver, Seattle, Virginia Beach, Columbus, Miami, Olympia, appliance repair Los Angeles CA, Manchester, appliance repair Tucson AZ, appliance service Las Vegas, Minneapolis, Newark, Detroit, Richmond, Baton Rouge, Henderson, dishwasher service San Diego, Charlotte NC dishwasher repair, Chicago, Boston, Silver Spring, Bowie, Aurora, Providence, Reno City, Fort Worth, Louisville, Pittsburgh, Portland, Omaha, Charleston SC appliance service, Houston The post How to Fix A Washer That Shakes and Moves appeared first on OnSite Appliance The dryer is an extremely useful appliance, especially during winters and rainy season. Your washer may clean your clothes but your clean clothes are of no use, if they aren’t dry. Like any other home appliance, even your dryer can malfunction. One of the problems your dryer could develop is taking too long to dry your clothes. When you face this problem or any other problem with your residential appliance, you can get help from a dryer service technician. When you call a service company that offers home repairs of a dryer, they will send a dryer technician to your place to troubleshoot the problem with your machine. To get details of a dryer repair person near me, you can get help of your friends or neighbors, who have used the services of a dryer repairman. Once you get details of a few dryer repair near me, you can approach them to fix the problem with your machine. Alternately, you can attempt dryer repair without getting help from a professional dryer service repair technician. To do this, you must be able to identify the part that is preventing your machine from drying your clothes. Here is a list of parts that could be responsible for the problem with your machine. Lint Filter When the machine’s lint filter is full of debris, it will restrict the airflow and increase the drying time. To keep your machine in perfect condition, you must clean the household appliance after every use. At times, a buildup of fabric softener in lint filter can restrict the airflow. To troubleshoot this problem, you must clean the filter using soapy water. If the lint filter is damaged, replace it immediately. Blower Wheel If the blower wheel of your household appliance is not firmly attached, it can cause the drive motor to slip. This will prevent the air from moving fast enough to dry your clothes properly. At times, the airflow is so less that it will trip the high limit thermostat and turn off the dryer’s heat circuit. When the blower wheel is loose, you will usually hear a rumbling noise during the drying cycle. Coil If you have a gas dryer in your house, delayed drying may be due to defective gas valve coils. Check the flame ignition of your machine if you suspect that valve coils are defective. Drum Seal The drum seal of your dryer prevents excess air from entering the dryer. Also, it acts as a cushion between the rear and front bulkheads and the drum. The seal is usually made of felt or some other similar material. Regular use of the dryer can wear out the seal. This will create a gap between the tub and the body, where the clothes can get stuck during the drying cycle. This will produce a thumping or scraping noise and can also damage the clothes. Door Seal When the door of the dryer is closed, it prevents cool air from entering the machine. When cold air does not enter the machine, it helps in drying the clothes efficiently. If your clothes are not drying properly, you must check the condition of the seal. If it is damaged or worn
Other service locations in popular cities: TucsonAlbuquerque, Salt Lake City, Jacksonville FL, Billings, Orlando, Tallahassee, Columbus, Little Rock, Miami, Bowie, New Haven, Henderson, Charlotte, Portland, Provo, Charleston SC, Indianapolis, New York City, Raleigh, Virginia Beach, Allentown, Baton Rouge, Milwaukee, St. Louis, Manchester, Reno City, Las Vegas, Everett, Nashville, Aurora, Birmingham, Tampa, San Jose, Dallas, Cleveland, Oklahoma City, Kansas City, Middletown, Richmond, Tacoma, Atlanta, Newark, Minneapolis, Fort Worth, Denver, Philadelphia, Boston, San Antonio, Pittsburgh, Colorado Springs, Jackson, Chicago, San Francisco, Louisville, Silver Spring, Columbia, Olympia, Detroit, Lakewood, Los Angeles, Seattle, Baltimore, San Diego, Omaha, Providence, Houston, Portland, Eugene, Sacramento, Phoenix, Austin The post How To Fix A Dryer That Takes Too Long To Dry appeared first on OnSite Appliance The dishwasher is a durable appliance but regular use of the home appliance can wear out some parts. This can affect the normal functions of the residential appliance. A common problem faced by dishwasher users is water not filling in the household appliance. For any problem with the machine, you should get help from a dishwasher service technician. Today, there are many service companies that offer home repairs for dishwashers. These companies will send dishwasher technician to your house to troubleshoot the problem with your machine. Dishwasher repairman will identify the problem with the machine and give you an estimate before carrying out repairs. When selecting a dishwasher service technician, you use the internet to get details of dishwasher repair near me. However, if you plan to repair the machine yourself you must be able to identify the part that is damaged and have the tools to replace the part. Here are details of some parts that can prevent water from entering the machine.
Water Inlet Valve The inlet valve of the dishwasher fills the machine with the right amount of hot water. This valve is controlled by the electronic controller or the timer. You can find this valve near the lower access panel of the dishwasher. It is connected to two wires, a hot water inlet hose, and an outlet hose. If you suspect that the valve is responsible for the problem with the machine, you should check if there is power going through the water inlet valve. If there is no problem with the power supply, the valve could be defective and it must be replaced. Float A problem with the float can also prevent the dishwasher from filling the water during the wash cycle. The float can be found at the bottom of the machine and its job is to prevent the machine from overfilling with water. When the water enters the machine, the float will rise with the water. The float will direct the float switch to turn off the water supply, when the desired level is reached. When checking the condition of the float, make sure you remove any foreign objects or debris that restrict the movement of the float. If the float is working properly, you must check the condition of the float switch. Float Switch You can find the float switch below the float. When the switch is activated by the float, the power supply to the water inlet valve is stopped. This prevents the water from entering the dishwasher. Before you check the condition of the switch, you must check if the mechanical action of the float is working properly. Also, make sure the wires connected to the switch are secure. If everything is in perfect condition, you must remove the switch from the machine and check its continuity using a multi-meter. Door Switch The door switch is a simple mechanism that prevents the machine from operating when the door is not closed properly. If there is a problem with the switch, the machine will not fill with water. You can find the door switch near the door panel that is located at the top of the door. To check the condition of the switch, remove the wires that are attached to it. Now remove the switch and check its continuity using a multi-meter. If the switch is damaged, replace it with a new one.
Check Our Service Locations for Repair Services in these Popular Cities: AustinHouston, Albuquerque, Tucson, Billings, Orlando, Tallahassee, Charleston SC, Columbus, Little Rock, Miami, Bowie, New Haven, Henderson, Charlotte, Indianapolis, Raleigh, Milwaukee, St. Louis, Las Vegas, San Jose, Kansas City, Middletown, Richmond, Tacoma, Atlanta, Minneapolis, Boston, Colorado Springs, Jackson, Chicago, Louisville, Columbia, Portland, Aurora, Dallas, Olympia, Lakewood, Los Angeles, Baltimore, San Diego, Omaha, Providence, Portland, Eugene, Sacramento, Oklahoma City, Manchester, Jacksonville FL, Birmingham, Nashville, Allentown, Reno City, Tampa, Provo, Salt Lake City, Denver, Cleveland, Everett, Fort Worth, New York City, Virginia Beach, San Antonio, Baton Rouge, San Francisco, Silver Spring, Detroit, Newark, Seattle, Pittsburgh, Philadelphia, Phoenix The post How To Fix A Dishwasher That Will Not Fill With Water appeared first on OnSite Appliance Having a range or oven in the kitchen can help in reducing the time you spend in the kitchen. When the household appliance malfunctions, most people prefer getting help from an oven service technician. Repairing the range or stove can appear to be a big task, but if you know where to look, you can easily repair the machine. If your timer of the oven does not advance, the electronic board of the home appliance is likely to be the cause of the problem. The electronic control board controls almost all the functions of the oven. The control board operates both the broil and bake element of the appliance. If fault codes are not displayed, you should check for power supply to the elements. When there is no power supply to the elements, you should check the power at the appropriate relays on the control board. Since this is a live voltage check, it should be done by a professional oven repairman. If there is no power output from the relay, you should change the control board. If you are unable to identify the problem with your oven, you should get help from an oven technician. The oven repair technician will visit your house to service the machine. Popular Cities In Our Service Area: Allentown, Dallas, Denver, Austin, Jacksonville FL, Chicago, Orlando, Miami, Henderson, Atlanta, Charlotte, Indianapolis, New York City, San Jose, Lakewood, Charleston SC, Richmond, Jackson, Portland, Aurora, Olympia, Houston, Providence, Eugene, Manchester, Cleveland, Everett, Fort Worth, San Francisco, Silver Spring, Detroit, Seattle, Pittsburgh, Oklahoma City, Philadelphia, Phoenix, Columbus, Los Angeles, Salt Lake City, Tacoma, Baltimore, Boston, Provo, Sacramento, Louisville, Nashville, Baton Rouge, St. Louis, Raleigh, Portland, Colorado Springs, Kansas City, Albuquerque, Virginia Beach, Middletown, Milwaukee, Las Vegas, Billings, Tampa, New Haven, Tallahassee, San Diego, Little Rock, San Antonio, Birmingham, Reno City, Newark, Columbia, Omaha, Bowie, Minneapolis, Tucson The post How to Fix An Oven Timer That’s Not Advancing appeared first on OnSite Appliance When the door latch of the machine does not work properly, it can prevent the dishwasher from starting. This can be a big headache, but you can easily repair the household appliance if you know what to do. The latch of the machine serves two basic purposes – the first is to keep the door closed and the second is to push the machine’s safety switch. When the door is closed, it prevents water from spilling out of the house appliance. When the safety switch is pushed, it activates the motor and the control panel of the machine. If the machine attempts to run when the door is open, it indicates that you may have a faulty door latch. Here are some of the steps you can take to troubleshoot the problem in the home appliance: Testing Before you start dismantling your dishwasher, you must check out if the safety switch is the problem or the latch. To check the condition of the switch, turn on the house appliance with the door open. Then, locate the switch and press it. If the dishwasher does not start when the switch is pressed, it indicates that safety switch is the problem. You can troubleshoot the problem by replacing the switch. If the residential appliance starts when you press the switch, you must replace the latch. Check the Latch Before repairing or replacing the latch, you must inspect the condition of the latch closely. At times, food particles may get accumulated in the latch, which can prevent it from performing its natural functions. If you don’t take steps to clean the latch, the machine may stop working altogether. You can clean the latch using a small screwdriver and a rag. Now check if the problem is fixed. Lubrication At times, all it takes to repair the door latch is some spraying of silicone to lubricate the latch. This spray can be easily found in a hardware store. When spraying silicone on the latch, move the door latch back and forth using your finger to ensure all moving parts of the latch are lubricated. Check the condition of Strike Plate The strike plate is the part of dishwasher’s body and it is the part that the door latches on to when it is closed. If the alignment of the strike plate changes, the door of the appliance will not close properly. To check the condition of the latch, you can visually inspect the part and check for any twists or bends. Also, check if the strike plate is straight. If the latch is tilted, you can use the hammer to tap it back into place. This should solve the problem. If you are not sure, then close the door and check where the latch hits the strike plate. If the plate needs adjustment, just use the hammer to tap it back into its correct position. When all these steps fail, it is best to get help from a professional dishwasher repairman. The technician will visit your home to repair or service the appliance. Today, there are many service providers who can send washer technician, gas stove repair technician, refrigerator technician, dryer service technician, washer technician, and several other appliance repair technicians to your place to troubleshoot the problem in the appliance. However, make sure you get references from friends and family members before approaching these service providers. Here Are Our Service Areas In These Popular Cities: Little Rock, New Haven dishwasher repair, Eugene, Tacoma, dishwasher repair Phoenix, New York City dishwasher service, dishwasher service Middletown, Jacksonville dish washer service, Everett, Tampa, Lakewood, dish washer repair Philadelphia, St. Louis, Cleveland, appliance repair San Jose, Birmingham, Milwaukee, Oklahoma City, Allentown, Sacramento dishwashing machine repair, Kansas City, Colorado Springs, Billings, Salt Lake City, Raleigh, Tallahassee, San Antonio TX dishwasher service, Albuquerque, Austin, Columbia, Provo, Baltimore, Nashville, Dallas, Denver, Seattle, Virginia Beach, Columbus, Orlando, Miami, Olympia, appliance repair Los Angeles CA, Manchester, appliance repair Tucson AZ, appliance service Las Vegas, Minneapolis, Newark, Detroit, Richmond, Baton Rouge, Henderson, dishwasher service San Diego, Charlotte NC dishwasher repair, Chicago, Boston, Silver Spring, Bowie, Aurora, Indianapolis, Providence, Reno City, Fort Worth, Jackson, Atlanta GA appliance repair, Louisville, Pittsburgh, Portland, Portland, Omaha, Charleston SC appliance service, Houston, San Francisco CA dish washer repair The post How To Troubleshoot A Dishwasher Door Latch appeared first on OnSite Appliance A refrigerator is unarguably the most important appliance in our homes. However, noises from the refrigerator can be annoying. These strange noises from your home appliance may not only cause uncomfortable scenarios, but is also a health hazard. Therefore, it is important that you arm yourself with insightful knowledge on issues causing this problem and learn how to fix them. There are different parts of the refrigeration system that can cause this problem. So check each part carefully and get professional help to handle complicated refrigerator repair problems. Here is a quick guide to easily identify and fix the problem-causing parts. Condenser Coil Today, most refrigerator brands come with a condenser coil that is usually located at the bottom of the household appliance. The heat from the coil is removed through the condenser fan that allows the circulation of air within the coil. It also circulates air over the drain pan to prevent defrost water from damaging the condenser coil. If you can hear loud noises from the fridge, there could be a problem with the fan motor. Other symptoms of a problem in the fan motor include the fridge not staying cool or turning off abruptly. If the noise is coming from the rear bottom of the fridge, you must check the condition of the condenser fan. Before checking the fan, make sure that you’ve already disconnected the freezer from the power supply. Then, remove the access panel that is on the rear side of the refrigerator. Look for dirt and debris that may impede the fan from operating freely. You must ensure that the condenser fan is free from obstructions as obstructions can prevent it from circulating the air freely. To remove debris and dirt from the fan, you could use a vacuum cleaner. You also need to check the fan blade, if they are damaged or if the motor is worn out, you must replace them immediately. At times, the problem will be the worn out rubber grommets, so it will be best to replace them. Evaporator Fan Motor The fan of the evaporator motor is usually found in your freezer compartment. When the compressor is running, this fan pulls out air from the coils to regulate the refrigerator’s temperature. If the freezer area keeps on producing loud noises, the evaporator fan motor may not be broken. Other symptoms of problem with evaporator fan motor include ice taking a long time to freeze or the fridge not staying cold. When checking the motor and the fan, you must cut the power supply to the fridge before taking out the evaporator motor cover. If frost or ice is causing the noise, then defrost issues may be causing this noise. If the fan is damaged or loose, you must replace it. At times, the motor’s shaft may prevent the fan from moving freely. If there is an issue with this, you must replace the part immediately. Once you replace the problem part, reconnect the power supply temporarily. However, you must be extremely careful when reconnecting the power supply as there are several live circuits that can endanger the life of the person carrying out the refrigeration repairs. If possible, carry on the fridge repairs under the guidance of a service professional. Evaporator Fan Motor Grommet This part helps in reducing the vibration noise by acting as the separator that isolates the motor from the mounting bracket. The grommets may develop wear and tear and can be the source of excess noise. Check the evaporator fan and look for the motor grommet to check if it is worn out. Make sure you disconnect the power supply before checking the condition of the grommet.
Other parts that could cause noises include the damper control and the compressor. If diagnosing these repair issues seem too complicated, give us a call today to set up a same day service call with one of our expert service technicians or a repairman for the following cities: Atlanta refrigerator service company, San Antonio, Chicago, Middletown refrigerator repair company, Jacksonville refrigerator repair service, Charleston appliance service company, Fort Worth, Houston, Dallas, refrigerator repair service New Haven, Tampa, Little Rock, refrigerator & freezer repair Charlotte, Everett, Baton Rouge, Sacramento refrigerator repairman, Birmingham, Oklahoma City, Columbia, Reno City, Los Angeles refrigerator repair technicians, Jackson, Columbus, Newark, Albuquerque, Manchester, Baltimore, San Diego, Philadelphia refrigeration machine repair, Richmond, Minneapolis, freezer repair Las Vegas, Omaha, Kansas City, Nashville, Eugene, Portland, Denver, Phoenix appliance service, refrigerator technician San Jose, St. Louis, Detroit, Tacoma, Henderson, Milwaukee, Pittsburgh, Raleigh, Salt Lake City, Provo, Louisville, Olympia, Miami, Tucson appliance service company, appliance repair experts in New York City, Portland, Austin, Boston, Orlando, Virginia Beach, freezer repair service in San Francisco, Billings, Cleveland, Providence, Seattle, Tallahassee, Indianapolis, Colorado Springs, Bowie, Lakewood, Aurora, Allentown, Silver Spring The post How To Fix A Noisy Refrigerator? appeared first on OnSite Appliance The timer of a washing machine is an important programming tool that regulates power supply to various parts of the machine. It consists of a control switch, which is usually found in the main control panel of the washer. The model of the switch will vary depending on the brand of the washing machine you use. Some brands use mechanical clocks which resemble the normal clock, while others use electronic clock to regulate the machine. The timer of the machine induces the machine to perform a task for a specific length of time. The start switch of the machine, which is usually a part of the timer knob helps in setting the time of washing and drying cycle. When you pull or push the knob, it activates the cycle. The knob can be either electronic or mechanical, depending on the model of the machine. If there is a problem with the knob, it can be repaired only by a washer repair technician. Types The knob and selector switch vary depending on the brand of a machine. The washer will operate only when the timer is in perfect condition. The timer is usually the start button of the machine. If you have a digital washing machine in your house, the functions of the machine are controlled by an electronic switch. Most modern washers use electronic switch to control the functions of the machine. However, a mechanical switch is considered better than an electronic switch as it is more durable. Common Problems Since the timer controls most functions of the washer, even a minor problem with the timer can affect the functioning of the machine. Some functions controlled by the timer include tub draining and filling processes, water level of the tub and duration of a wash cycle plus all other important settings of the wash cycle. One of the common problems you are likely to face is loose connection. This problem can be solved by checking all the wires that are connected to the timer and fixing them securely to the terminals. At times, the timer may show a faulty time which can affect the wash cycle. If the selector knob is loose, it can get damaged due to inefficient handling. Another problem you could face is wires connected to the timer getting damaged or burnt. This problem can be solved by replacing the damaged wires. Splashing water on the timer can damage it. If the timer does not work if water is inadvertently splashed on it, you may have to replace the timer.
Tips If you have a washer that does not work, it is important to carry out repair or service properly, else, it could affect the functioning of the machine. Repairs cannot be carried out unless you are trained to handle them. This holds good for all other appliances you have in your home. For instance, if you have a fridge or dryer that is not working, you must get help from a trained dryer service technician or fridge repairman to solve the problem. Repairing household appliances without proper technical knowledge can endanger the life of people living in your house. We Provide In Home Appliance Service In These Popular Cities: Raleigh, Boston, Denver, washing machine repair Phoenix, Los Angeles washing machine repair, washer repair Charlotte, Provo, Aurora, San Jose washer repair, Everett, Dallas, Tucson, Louisville, Billings, Baltimore, Manchester, Little Rock, Reno City, Virginia Beach, Lakewood, St. Louis, Fort Worth, San Antonio, washing machine service Sacramento, washer service San Francisco, washer & dryer repair Las Vegas, Eugene, Charleston washer & dryer repair, Henderson, Albuquerque, Tampa, Oklahoma City, Columbia, Silver Spring, Richmond, Milwaukee, Olympia, Newark, Portland, Detroit, washer and dryer repair San Diego, Birmingham, Pittsburgh, Colorado Springs, Minneapolis, Salt Lake City, New Haven washer and dryer repair, Omaha, Orlando, Allentown, Tacoma, Jackson, Chicago, Columbus, Providence, Austin, Portland, Bowie, Atlanta, Tallahassee, Philadelphia appliance service, Indianapolis, Houston, New York City appliance service, Miami, Nashville, Cleveland, Baton Rouge, Seattle, Kansas City, appliance service Middletown NJ, washing machine repair Jacksonville FL The post Common Problems Associated With Washing Machine appeared first on OnSite Appliance Dishwashers can have an enormous impact on our life. Earlier most people used to clean their dishes manually, which was time-consuming and arduous. Today, most new dishwashers not only clean your dishes must also require less water. Also, this household appliance consumes less energy which helps in reducing our energy bills. In a recent study, it was found that an average hand-washer use a 3-kilowatt hour of electricity and 28 gallons of water to clean a sink full of dishes. On the other hand, the dishwasher uses just uses 2-kilowatt hours of electricity and 6 gallons of water to do the same job. No wonder why dishwashers have become the most common home appliance. If you have a dishwasher, and you use it on a regular basis, you are likely to face some problems in the machine. Some of the common problems you are likely to face include machine not starting, water draining out of the appliance, noisy, and several other problems. Having a noisy machine in your house can be a frustrating experience. Service or repair of the machine is not easy, especially if you are attempting a fix for the first time. Residential users, who find it difficult to fix the machine, should use the services of an experienced technician. However, if you still want to repair your noisy machine, you should know the parts that could be responsible for this problem. In this article, we have given information on the parts that are likely to cause this problem and the steps you must take to solve the problem. Defective Pump One of the reasons why your dishwasher is making strange noises is because the pump of the machine is defective. The main function of the machine pump is to pressurize the spray arm. In some models, it is also used to drain water from the machine. The pump is typically located at the bottom of the machine. It contains two compartments; one for draining the water and other to circulate water in the machine. The circulation part of the water pump will consist of the filter component and the wash impeller, while its drain portion will contain the chopper blade and the drain impeller. In some cases, the drain portion may also contain the solenoid-operated diverter. The drain impeller is driven by an electric motor that is attached to the side or the bottom of the water pump. If the machine is noisy, you must check the condition of both sections of the pump. Never attempt dishwasher repair without disconnecting the power supply to the machine. If you are unable to solve the problem, it is best to get help from dishwasher repairman. Wash Arm Seal Your dishwasher could be noisy because the bearing ring or the wash arm seal of the dishwasher may be damaged. The seal is a plastic ring the supports the spray or wash arm of the machine. If the seal is worn out or loose, it could prevent the spray arm from functioning properly. You must inspect both the ring and the seal and replace it if required. Spray Arm Check the condition of the spray arm to ensure it turns freely and does not hit the dishes or the rack. If the spray arm wobbles, the hub or the center portion of the spray arm may be worn out, and the spray arm must be replaced. If you find it difficult to replace the arm, get help from dishwasher service technician. We also offer our services in these popular cities: Henderson, dishwasher repair Sacramento, Dallas, Baltimore, Manchester, Portland, Salt Lake City, Providence, Miami, Aurora, Austin, dishwasher repair San Jose, Billings, Milwaukee, Boston, Albuquerque, Seattle, dishwasher repair technician Charlotte, Philadelphia dishwasher repair, Louisville, Provo, Newark, Silver Spring, Oklahoma City, dishwashing machine repair San Diego, Birmingham, Atlanta GA dishwasher repairman, Fort Worth, Portland, Minneapolis, San Francisco dishwasher , Olympia, Reno City, Little Rock, Bowie, Everett, Pittsburgh, Tallahassee, Jackson, Detroit, Nashville, Richmond, Allentown, Charleston SC dish washer service, Columbia, San Antonio, St. Louis, dish washer service in Las Vegas, Tacoma, Denver, Houston, Baton Rouge, dish washer repairman New Haven, dishwasher technician Middletown, Los Angeles CA appliance repairmen, Colorado Springs, Raleigh, Tampa, Indianapolis, Orlando, appliance repair New York City, Eugene, Lakewood, Jacksonville FL appliance technician, Tucson dishwasher machine repair, Kansas City, Cleveland, appliance repair Phoenix AZ, Omaha, Chicago, Columbus, Virginia Beach The post How To Fix A Noisy Dishwasher appeared first on OnSite Appliance |
About UsOnSite appliance repair technicians specialize in fixing all major home appliances, so you can have peace of mind that any appliance repairman we send to your home in will not only be experienced but certified to work on your residential appliance. ArchivesNo Archives Categories |