Microwaves have capacitors that store excess electric energy, especially when there is a sudden power discharge or surge. It helps maintain the consistency of the electric supply to the microwave. Electrical gadgets may encounter occasional disturbances, and your microwave is not an exception. So, whenever you try to fix the device, it is wise to discharge its capacitor so that no one gets hurt while doing microwave repairs. Checking the chargeYour first step is to take the capacitor out of its power source. Unplug the microwave so that there is no power in the device. Take a multimeter and set the highest DC voltage on it. This will help to get the most accurate reading of the capacitor. Take the probes of the multimeter and connect them to the capacitor’s posts. Try touching the red lead of the multimeter to one of the posts of the capacitor. Then touch the black lead to the other post. You can also hold both the leads on the posts together. The moment the leads touch the posts, the multimeter flickers. It will display the current voltage available in the capacitor. Keep touching the capacitor until the power reaches below ten volts. Ideally, it should reach zero so that you know that the capacitor is completely discharged. Using a screwdriverDon’t have a multimeter in your house? Don’t worry; you can discharge the microwave using a screwdriver also. Try to stay away from the capacitor terminals while doing this. Take an insulated screwdriver with plastic or rubber handles. Make sure it doesn’t have any crack. Grab the bottom half of the capacitor firmly. Don’t squeeze it too hard. Touch the posts of the capacitor with the tip of the screwdriver. You will notice crackling sounds and sparks flaring from the capacitor terminals. The screwdriver needs to touch both the posts together; otherwise, this step will not work. Keep touching the terminals until you don’t see any spark or crackling noise from it. This will mean the capacitor is fully discharged. You can touch the terminals again to confirm. Making a capacitor discharge toolThis is a time-consuming process that involves using alligator clips, 20k OHM 5 watt resistor, and 12-gauge wire. Cut the 12-gauge wire into two equal parts of 15cm each. Slash approximately 1.5cm of insulation from one end of each wire. Solder one end of the wires and wrap these ends using a shrink wrap or electrical tape. Take the alligator clips and solder them to the other end of the wire. Slowly connect these clips to the two terminals of the capacitor of the microwave. It will quickly discharge the capacitor. You can use a multimeter to check the voltage left in the capacitor to proceed with the repair of the microwave. Now that you know how to discharge microwave capacitor, don’t overlook any of the steps as mentioned. These are the quickest methods to discharge a capacitor that don’t require too many items. Other service locations in popular cities: Franklin Township Dishwashing Machine Repair, Lexington Appliance Repair Technician, Houston, Henderson, Reno City, Omaha, Albuquerque, Fort Worth, Cleveland, Jacksonville FL, Virginia Beach, Detroit, Louisville, Aurora, Colorado Springs, Jackson, Phoenix, Salt Lake City, Richmond, Silver Spring, San Antonio, Everett, Charlotte, San Francisco, Middletown, Boston, Seattle, Pittsburgh, San Diego, San Jose, Tacoma, New York City, Tallahassee, Baltimore, Baton Rouge, Minneapolis, Allentown, Billings, Oklahoma City, Olympia, St. Louis, Providence, Lakewood, Provo, Los Angeles, Tampa, Dallas, Columbus, Birmingham, Eugene, Portland, Sacramento, Kansas City, Chicago, Indianapolis, Denver, Tucson, Milwaukee, Philadelphia, Austin, Raleigh, Columbia, Las Vegas, Manchester, New Haven, Atlanta, Fort Lauderdale Appliance Repair, Washington DC Refrigerator Repair, Biddeford Washing Machine Repair, Hackensack Dryer Repair , Ramapo Appliance Service, Alexandria Oven Repair, Vernon Township Stove Repair, Paterson Range Repair, Parsippany-Troy Hills Freezer Repair, Elizabeth Dishwasher Repair, Jersey City Washer Repair, Edison Fridge Repair, Nashville, Orlando, Miami, Newark, Little Rock, Bowie, Charleston SC The post How to Discharge Microwave Capacitor appeared first on Appliance Repair Houston
0 Comments
House appliances such as dryers, washing machines, microwave, and refrigerator have become an integral part of our life. When there is a problem with any of the household appliances, it can upset your daily routine and make life difficult. It is therefore important that you take good care of your appliances. Some of steps you can do to take care of your appliance are regular dryer servicing, cleaning the appliance after every use, repairing the broken appliance as soon as possible. When you follow these simple steps, you are less likely to face problems with your residential appliance. The dryer may have seasonal use but it is an extremely useful appliance. During winters and rainy season, drying your wet clothes is a pain, if you don’t have a dryer at home. Like any other machine, even your dryer could malfunction. For instance, some machines may shut off early, which can leave the clothes wet. If you face this problem, you should ideally get help of a dryer technician. To get details of dryer repairman near me, all you have to do is type “Dryer repair in my area” in any search engine. Within a few seconds, you will find details of all companies that Today, most dryers are equipped with a moisture sensor that controls the machine timer when the user selects the automatic drying option. The sensor circuit of the dryer includes an electronic control in the machine console. The sensors are usually located in the front bulkhead. When you select the sensor dry option, the wet clothes in machine come in contact with the sensor, which completes an electronic circuit. The circuit causes the capacitor of the control board to discharge and prevents the machine timer from advancing. When the clothes inside the machine are nearly dry, the electric circuit is incomplete and the timer starts moving. When the sensor is defective or is coated with detergent, the machine will shut-off before your clothes are dry. Other service locations in popular cities: Houston, Henderson, Reno City, Omaha, Albuquerque, Fort Worth, Cleveland, Jacksonville FL, Virginia Beach, Detroit, Louisville, Aurora, Charlotte, San Francisco, Middletown, Boston, Seattle, Pittsburgh, San Diego, San Jose, Providence, Lakewood, Provo, Los Angeles, Tampa, Dallas, Columbus, Birmingham, Eugene, Portland, Sacramento, Kansas City, Chicago, Indianapolis, Denver, Nashville, Orlando, Miami, Newark, Little Rock, Bowie, Charleston SC, Tacoma, New York City, Tallahassee, Baltimore, Baton Rouge, Minneapolis, Allentown, Billings, Oklahoma City, Olympia, St. Louis, Colorado Springs, Jackson, Phoenix, Salt Lake City, Richmond, Silver Spring, San Antonio, Everett, Tucson, Milwaukee, Philadelphia, Austin, Raleigh, Columbia, Las Vegas, Manchester, New Haven, Atlanta The post How To Fix A Dryer That Shuts Off Too Soon appeared first on OnSite Appliance Have you been in a situation where your washing machine or any home appliance stops working when you are expecting guests or when you have a party in your house. Having a broken appliance, especially when you have guests, can spell disaster in most homes. One of the problems you are likely to face with your washer is if the wash tub won’t spin. When you face this problem, it is best to get help from a washer repair person. Ideally, washer repair and washer service must be done by a professional. This is because the machine may contain certain complicated parts that are best handled by a washer technician. When you contact a washing machine service technician, the washer repairman will try to understand your problem and offer the best solution. For any washing machine repair help, you should use the services of a professional that is close to your place. If you are wondering, “How do I get details of a washer repair in my area?” All you have to do is type “Washing machine repairman near me” in any search engine, followed by your area code. This will give you the details of all companies that offer washer repair near me.
The door lock of your washer is called the interlock. This safety feature prevents the machine from operating when the door of your top or front loading washer is not closed properly. The interlock has two parts; one is fixed on the machine body and other on the door. The part that is attached to the machine body contains a switch. This switch indicates to the control board that the door is closed and it allows the spin cycle to operate. When there is a problem with the interlock, it may not lock the machine door properly or it may prevent the switch from operating. This will prevent the wash tub from spinning. In some washer models, the machine will display a code when there is a problem with the interlock. If your washer displays this code, just change the interlock and your machine will start functioning normally. Before replacing the interlock, disconnect the power supply to the machine.
Clutch Assembly
Drive Belt If you use a top load washer, the belt connects the transmission to the drive motor. On the other hand, if you have a front load washer the belt connects the wash basket to the drive motor. If the belt is damaged due to excessive wear or because of overheating, the machine will not spin. Before you replace the belt, check the condition of idler pulley and motor glide. If you are using a top load washer, you should check the movement of the transmission pulley and wash basket. You should also check for signs of water or oil leakage near the pulley area. If you use a front load washer, you should ensure that the wash tub moves freely. When replacing the belt, make sure you get the same make and size. This is necessary for proper performance of the machine. When replacing the belt, disconnect the power supply to the machine. Popular cities we service:
The post How to Fix A Washer That Won’t Spin appeared first on OnSite Appliance Having a faulty appliance in your house can be a pain, especially if you have guests at home or throwing a party. Imagine, your microwave stops working when you have invited your friends. Your routine gets affected and you get tense and tired. Therefore, it is important that you take care of your residential appliance to prevent last minute disasters. Appliances that you use almost every day are more likely to malfunction. Your refrigerator and washer are two appliances that you use almost every day. When your washer malfunctions, it is best to get help from a washer service technician. This is because your household appliance has several parts that can only be repaired or replaced by a washer technician. Today, getting a washer repairman to visit your place for washer service or washer repair is easy. All you have to do is give a washer service repair company a call and within no time the washer repair person will be at your place. If you are looking for a good washer repairman near me, all you have do is type “Washer repair near me”, followed by your current residential address, in any search engine. The search engine will display details of all the service providers in your area. Alternatively, if you plan to repair the washer without professional help, you must identify the parts that are responsible for the problem with your machine. If your washer fills and drains at the same time, here are the parts that could be responsible for the problem. Water Intel Valve The inlet valve of your washer is responsible for filling the washtub with hot, warm, or cold water. The working of these valves is controlled by a solenoid which is operated by the electronic control board or the timer. In some washers, the solenoid is also controlled by the pressure or water level switch. If the water enters the tub during the drain cycle, it could be due to the faulty valve. To check the condition of the valve, disconnect the power supply to the machine when this symptom occurs. If the water continues to enter the tub, it means the inlet valve is defective. On the other hand, if the water stops filling, the problem could be in the switch or electronic circuit board. Water Level Switch This switch helps in detecting the correct water level in the washtub. The switch is normally found behind the washer’s control panel. The switch and the tub are usually connected by a dome tube or a hose. When certain water level is reached, the air in the dome tube will push against the diaphragm inside the water level switch. This will turn off the water supply to the tub when the desired water level is reached. If there is a problem with the tube, pressure may not be created to activate the water level switch and water may overflow from the machine. Before you check the switch, you must check the condition of the dome hose. If it is cracked or worn out, replace it You Can Check The Popular Cities We Service Here: Reno City, Omaha, Albuquerque, Fort Worth, Cleveland, Virginia Beach, Detroit, San Jose, Louisville, Aurora, Charlotte, Atlanta, San Francisco, Middletown, Seattle, Pittsburgh, San Diego, Austin, Tampa, Dallas, Columbus, Sacramento, Kansas City, Indianapolis, Denver, Nashville, Orlando, Miami, Newark, Little Rock, Tacoma, New York City, Tallahassee, Baltimore, Baton Rouge, Minneapolis, Allentown, Billings, Oklahoma City, Olympia, St. Louis, Colorado Springs, Los Angeles, Jackson, Phoenix, Salt Lake City, Richmond, Silver Spring, Charleston SC, San Antonio, Everett, Tucson, Milwaukee, Philadelphia, Raleigh, Columbia, Las Vegas, Manchester, New Haven, Chicago, Providence, Jacksonville FL, Provo, Henderson, Lakewood, Bowie, Houston Eugene, Birmingham, Boston, Portland The post How to Fix A Washer That Fills and Drains At The Same Time appeared first on OnSite Appliance Have you ever faced a situation when your dishwasher stops working when you have guests or have thrown a party? You are not alone, as there are thousands of homeowners who have faced a similar situation. Dishwasher repair and dishwasher service is not difficult if you know where to look. Ideally, you should use the services of a local dishwasher repair company because you can easily approach them in case of an emergency. Another benefit of using a dishwasher repair person near me is that down time is less. Most local dishwasher service repair companies will send their dishwasher technician on the same day. This means that you can use your broken appliance on the same day or in a very short period of time. To get details of a local dishwasher service technician, just visit any popular search engine and search for “Dishwasher repair near me”. This will give you an idea of all the services where to find a dishwasher repair handyman in your area. If your dishwasher stops working, it is imperative that you use the services of a dishwasher repairman. However, if you consider them expensive, you can try to repair the home appliance yourself. One of the problems you are likely to face is dryer not dispensing the detergent properly. Here are the details of some parts that can prevent your residential appliance from dispensing detergent. Detergent Dispenser The dispenser has two main compartments that release detergent during the wash cycle. The first compartment releases detergent using the prewash cycle, while the second compartment releases detergent during the main cycle. If the dispenser is clogged with powder, you just have to clean the dispenser to troubleshoot the problem. At times, a damaged part of the dispenser may prevent it from releasing the detergent. To troubleshoot this problem, you will have to replace the damaged part. Rinse aid cover or cap A problem with the cap or cover may be the reason why the house appliance is not releasing rinse aid. This part can be found in the inner door panel of your house appliance. If the cap is loose, just refit the cap to rectify the problem. If the cap is damaged, you may have to replace it. Hinge Pin and Door Spring At times, the machine may not release detergent because the pin and spring of the dispenser door are faulty. The door of the dispenser is spring loaded and catch loads the door in the closed position. If the spring and pin is bent or broken, you have to replace these parts. If these parts are in perfect condition, you have to check the condition of the bi-metal release, time, and the wax motor. Any problem with these parts can prevent dryer from releasing detergent. Wax Motor The wax motor is a part that you commonly find in most modern dishwashers. The motor is used to release the dispenser door catch. If there is a problem with the wax motor, the dispenser door will not be open and the machine will not release any detergent. This motor acts as a solenoid when it is activated by the machine’s control or the timer. The piston inside the dispenser acts as a mechanism that releases the catch of the dispenser door. When checking the condition of the motor, make sure it gets power at the right time. If this is not the case, you may have to replace it. To check the condition of the wax motor, you will need a multi-meter. Bi-Metal Release If you are using an old model dryer, you will not find the wax motor in your machine. Instead, you should look for the bi-metal release that operated the dispenser door. This part uses electricity to generate action to release the dispenser door catch. When checking the condition of the release, make sure it is getting power at the right time. Also, check its continuity using a multi-meter. Timer Some dryers have a timer that operates the dispenser mechanically. During the cycle, the timer activates the lever that releases the door catch. When checking the condition of the timer, make sure then link between the door catch and the timer is in perfect condition. If the linkage is faulty, replace it immediately. Also, check the condition of the cam. If the cam is worn out or damaged, you must replace it. We also offer our services in these popular cities: The post How to Fix A Dishwasher That Won’t Dispense Detergent appeared first on OnSite Appliance Oven, stove, and range are an indispensable part of modern kitchens. They make your job in the home kitchen less cumbersome and take less time to cook your favorite dish. However, like any other home appliance even your oven or range could malfunction. Ideally, you should look for a technician that offers household oven repairs. Since repairing the oven requires high voltage test, it is best to allow oven service technician to carry out oven repairs. The oven technician will visit your house at your convenience to troubleshoot the problem with your machine. However, if you don’t plan to use the services of an oven repairman, you must know which part could be responsible for the problem with your machine. At times, a problem in your oven can affect the programming feature of your residential appliance. Here is a quick guide to help you identify the problem part and service your machine. Membrane Switch and Electronic Control Board In most modern ovens, the programming functions are controlled by the electronic control board. Usually, a problem with the keypad or the membrane switch can prevent you from selecting a program. In some machines, a separate membrane switch is used. In these machines, you may have to only replace the membrane if the keypads don’t work properly. The membrane switch is usually attached to the control board using the ribbon connector. To check the condition of the board and the membrane switch you will need a multi-meter. Here Are Our Service Areas In These Popular Cities: Tucson AZ, Orlando, Charlotte NC, Las Vegas, Seattle, Little Rock, Chicago, Denver, Charleston SC, New Haven, Eugene, Portland, Tacoma, San Francisco CA, Phoenix, Detroit, New York City, Providence, Portland, Middletown, Jacksonville, Indianapolis, Omaha, Miami, Everett, Virginia Beach, Boston, Tampa, Columbus, Lakewood, Philadelphia, St. Louis, Newark, Cleveland, Pittsburgh, Reno City, Louisville, San Jose, Birmingham, Atlanta GA, Milwaukee, Oklahoma City, Allentown, Henderson, Bowie, Sacramento, San Diego, Silver Spring, Baton Rouge, Jackson, Houston, Fort Worth, Tallahassee, Los Angeles CA, Kansas City, San Antonio TX, Olympia, Colorado Springs, Minneapolis, Billings, Manchester, Salt Lake City, Raleigh, Albuquerque, Austin, Columbia, Aurora, Dallas, Provo, Baltimore, Richmond, Nashville,
The post How to Fix An Oven That Won’t Program appeared first on OnSite Appliance Most people who have a dryer in their house undermine its importance. They consider it to be not so important home appliance because it has limited use. Only when the residential appliance stops working, they realize how difficult their life can be without it. This is especially true during rainy season and winters, when drying your dirty clothes is a pain. When you use your dryer regularly during winters, some parts of the household appliance can malfunction. When you face such a situation, don’t PANIC! Your ideal option would be to get help from a dryer service technician. The dryer technician should offer home repairs and if possible must visit your place on the same day. The dryer repairman will be able to visit your home on the same day if you use the services of a local dryer repair company. If you are looking for a good dryer repair near me, you can get help from neighbors, friends and colleagues. You could also use the internet to get these details. Just type “Dryer repair near me” followed by your area code to get a list of companies that offer dryer service repair. If you plan to repair your dryer without any help from a dryer repair technician, you should know the parts that are faulty. If your machine does not shut off, here are the details of some parts that could be faulty: Door Switch Most modern dryers have an in-built safety feature known as the door switch. This switch does not allow the appliance to work when the door is open or not closed properly. If your machine is working when the door is open, it means the door switch is faulty. The door switch is usually fixed behind the front panel of the dryer. Once you locate the switch, you can check its continuity using a multi-meter. If it has more than one terminal, make sure you check the condition of all the terminals. These tests must be performed when there is no power supply to the machine. Timer The timer is usually attached to the control console of the dryer. The timer includes a motor that is attached to several parts of the machine. The timer regulates the working of these parts to complete the program selected by the user. If there is a problem in the timer motor or contacts, the dryer will not shut off. When the timer is defective, your only option is to replace the timer. Before replacing the part, make sure you check the condition of the timer using a multi-meter. Of course, this must be done after the machine is unplugged. Cycling Thermostat Dryer with Auto Dry feature use a cycling thermostat to advance the timer and regulate the temperature inside your machine. The thermostat controls the timer motor and the heat source to maintain the drum temperature. When checking its condition, make sure there is power supply to and from thermostat. This is a live voltage test and must be done under the supervision of an expert. Cool Down Thermostat Some machines have a cool down thermostat that tumbles the clothes with using heat. This usually happens at the end of the drying cycle. The power required to turn the tub is sent to the drive motor through the cool down thermostat. If this thermostat is faulty, it will allow the drum to rotate indefinitely. You can check the condition of the thermostat using a multi-meter, after you disconnect the power supply to the machine. Locations We Serve in Popular Cities: Omaha, Virginia Beach, Louisville, Atlanta, San Diego, Columbus, Little Rock, Billings, Oklahoma City, Silver Spring, Everett, Manchester, New Haven, Bowie, Birmingham, Boston, Milwaukee, Pittsburgh, Charleston SC, Allentown, San Antonio, Tacoma, Providence, Houston, Orlando, Miami, Tampa, Richmond, Denver, Eugene, Los Angeles, Las Vegas, St. Louis, Philadelphia, Sacramento, Portland, New York City, Jacksonville FL, Columbia, Fort Worth, Reno City, Seattle, San Francisco, Baton Rouge, Albuquerque, Dallas, Provo, Henderson, Salt Lake City, Aurora, Baltimore, Phoenix, Charlotte, Newark, Indianapolis, Tallahassee, Tucson, San Jose, Raleigh, Jackson, Colorado Springs, Middletown, Chicago, Detroit, Olympia, Cleveland, Minneapolis, Nashville, Lakewood, Austin, Kansas City The post How To Fix A Dryer That Won’t Shut Off appeared first on OnSite Appliance With the advent of dishwasher, cleaning dishes has become easier and less time-consuming. Earlier, we would have to spend several hours cleaning the dirty dishes. Today, all we have to do is put our dishes in the dish washer and let the house appliance do its job. Within a short period, the dishwasher has become an indispensable part of our home. However, like any other residential appliance, even the dishwasher can develop a problem. When your dishwasher malfunctions, it is best to opt for home repairs for dishwasher. You can find details of a dishwasher technician in your area and call them to troubleshoot the problem with your household appliance. The dishwasher service technician will visit your place to repair or service the machine. If you plan to attempt the dishwasher repair yourself, make sure you are aware of the parts that could be responsible for the problem. At times, your dishwasher may not clean the dishes properly. If you plan to repair the machine without the help of a dishwasher repairman, you should know which part could be responsible for the problem. Here is a brief guide to help you. Discharge Housing Gasket If the water pressure from the machine’s spray arm is low, the housing gasket of the upper discharge could be responsible for the problem. The gasket is usually located on the discharge cover just above the impeller. The housing gasket may have got dislocated or may need replacement. If the gasket is damaged and must be replaced, make sure you remove all the debris from the area before installing the new gasket. Spray Arm A problem with the machine’s lower spray arm could prevent the home appliance from cleaning the dishes properly. The spray arm is responsible for spraying strong stem of detergent and hot water on the dishes. Before you check the condition of the spray arm, make sure it is able to move freely and is not obstructed by the dirty dishes. At times, the bearing ring of the spray arm may be dislocated or worn out, which can cause the arm to wobble and prevent it spraying water and detergent evenly. If the bearing ring is not worn out or dislocated, you should visually inspect the spray arm for plugged holes or cracks. Food particles, glass, toothpicks, and other debris can clog the holes of the spray, which can impair the direction or force of the spray arm. If there are cracks on the spray arm, it will reduce water force and prevent the machine from cleaning the dishes properly. Docking Station Some dishwashers have a middle spray arm which is attached to the machine’s upper rack. In these machines, you must check the docking station and its flappers. The docking station, which has two outlets, provides water to the machine’s middle spray arm. Make sure the docking station is connected properly to the tube that supplies water to the machine. Also, make sure the flappers move freely and close securely to prevent pressure loss when the supply tube of middle spray arm is not inserted. Chopper The dishwasher is equipped with a food chopper that is responsible for chopping the leftover food particles into small pieces so that they can be easily drained out from the washer. If the chopper isn’t fine enough or is broken, it can clog the drains. When your washer is not cleaning the dishes properly, you should check the drains. If the drain is clogged by large food particles, you must the check the condition of the chopper.
Water Inlet Valve A part of the dishwasher that is most likely to fail and prevent the machine from cleaning the dishes properly is the water inlet valve. The valve is located near the lower access panel which is usually in the front of the machine. If water level is not maintained or the machine does not have water, you must first inspect the valve to ensure that power is supplied to the valve when water enters the machine. You can check this using the multi-meter. If there is no problem with the power supply, the valve must be replaced. Water Delivery Tube In machines that have upper spray arm, a problem in water delivery tube can prevent the washer from cleaning the dishes properly. The tube is usually made of plastic and it is responsible for supplying water to the upper spray arm. When checking the condition of the tube, make sure it is properly aligned with spray arm and there are no obstructions. Filters Most dishwashers are equipped with at least one filter to remove debris from machine during the wash cycle. These filters come with a self-cleaning feature but under detergent use or certain water conditions, it can become clogged. The filter is usually a part of the pump or wash arm assembly. If you suspect that the filter is not doing its job, you should clean the filter. If cleaning does not help, you may have to replace the filter. Wash Spinner The wash spinner is a wash arm that is usually on the manifold or on the water feed tube. If the spinner is dislocated or cracked, it could prevent the machine from cleaning the dishes properly. Detergent Dispenser A problem with the detergent dispenser could prevent the washer from cleaning the dishes. Ideally, you must use a good quality detergent to wash the dishes. If you use tablets or gel, try switching to powered detergent because it dissolves faster. Some machines have a pre-wash compartment in their detergent cup. You could use this to add detergent to the machine. Also, it is important to use a detergent that suits the local water conditions. For instance, if you use hard water to clean the dishes, you will need more detergent to clean the dishes. However, avoid using too much detergent because it could damage the glassware. The detergent dispenser may not be working properly because the dispenser cup could be caked or clogged with the old detergent. To troubleshoot this problem, all you have to do is clean the cup. Also, make sure detergent is released by the detergent cup during the wash cycle. Heating Element For the washer to clean the dishes properly, a temperature of about 142 degrees Fahrenheit must be maintained. The heating element is used by the washer to maintain the temperature of water inside the machine. It is important to note that when you select the normal wash cycle, the heating element does not play any role in heating the water. So, when you select the normal cycle, make sure the water is hot enough to clean the dishes. Avoid using very hot water to clean the dishes, as it could damage the dishes. Before you start the wash cycle, run the hot water in the sink for 5 to 10 minutes. If the temperature of water drops during the cycle, the heating element could be the culprit. Since the heating element cannot be repaired, you may have to get a replacement. Pump Impellers The dishwasher has two impellers – the drain impeller and the wash impeller. These impellers are located inside the dishwasher. The wash impeller is responsible for circulating water inside the machine and pressurizes the water spray arm. The drain impeller is used to drain from the machine. To check the condition of the impellers, you can visually inspect them. If the fins or hub is damaged, you may have to replace it. Check for the communities that we service in popular cities: Houston, Las Vegas, Little Rock, Charleston SC, New Haven, Eugene, Tacoma, San Francisco CA, Phoenix, New York City, Portland, Middletown, Aurora, Jacksonville, Omaha, Everett, Boston, Tampa, Lakewood, Philadelphia, St. Louis, Cleveland, Pittsburgh, Reno City, Louisville, San Jose, Birmingham, Atlanta GA, Milwaukee, Oklahoma City, Allentown, Bowie, Sacramento , Baton Rouge, Jackson, Fort Worth, Kansas City, Colorado Springs, Billings, Salt Lake City, Raleigh, Albuquerque, Austin, Columbia, Provo, Baltimore, Nashville, Dallas, Denver, Seattle, Portland, Virginia Beach, Columbus, Detroit, Providence, Orlando, Miami, Olympia, Los Angeles CA, San Antonio TX, Manchester, Tucson AZ, Minneapolis, Newark, Richmond, Henderson, San Diego, Charlotte NC, Chicago, Silver Spring, Indianapolis, Tallahassee The post How To Fix Dishwasher That Won’t Clean Properly appeared first on OnSite Appliance Having a washer in our house has not only reduced our workload but has reduced the time we have to spend on cleaning our clothes. However, regular use of the washing machine can wear out a few parts of our household appliance. This can cause the machine to malfunction and upset our daily routine. Ideally, for any problem with your washer you should get help of a local washing machine repair company. Most local washing machine service companies offer home repairs, wherein, they send an expert washing machine repairman to your place. If you don’t know a good washing machine repair company in your area, you can use the internet to get details of washing machine repair person near me. Just go to any popular search engine and type “washing machine repair near me” followed by your area details. This will give you details of all companies offering washing machine service repair in your area. For most washer problems, it is best to get help from a washing machine service technician. However, before you call a technician you can identify the problem with your residential appliance. If you experience burning smell during the wash cycle, here is what you could do to identify and troubleshoot the problem. Spin Belt In some top loading washing machines, the transmission is driven by the belt. If your washer stops agitating, it could be due to the problem with the belt. To assess the condition of the spin belt, remove the front panel of the machine. After removing the panel, look for the belt at the bottom of your machine. The belt that is damaged will create a noise or cause a burning smell during the wash cycle. If there is no problem with the belt, assess the condition of the drive pulley. You should also assess the condition of the idler assembly before you replace the belt. When replacing the belt, make sure you get the exact replacement of your belt. Before you replace the belt, make sure you switch off the power supply to the machine. Pump Belt The belt is used to operate the machine’s drain pump. The pump belt is a normal v-shaped belt that attaches the drive motor to the drain pump. Some machines may use an idler pulley to maintain the tension on the pump belt. If you experience burning smell when your machine is operating, you should assess the condition of your pump belt. If the pump belt is damaged or worn out, it is best to get a new belt. When fixing the belt, make sure the pump turns freely when idler pulley is used. Also, check for signs of water or oil leakage on to the belt. All this must be done after power supply to the machine is disconnected. Motor Pulley The pulley is used by the drive motor to turn the pump and drive belt. It is designed to provide the maximum contact with the pump or drive belt. The belt is usually made of a synthetic material or plastic. When motor pulley is damaged or rusted, it can increase friction and damage the belt. When the drive or pump is not working, you should assess the condition of the motor pulley. If it is corroded or worn out, replace it with the new one immediately. Drain Pump The pump is used to drain water from the tub during and before the spin cycle. The pump is either motor driven, belt driven, or uses its own motor. If you experience burning smell during or after the wash cycle, it could be because the drain pump is damaged and it cannot turn. If you have a belt driven washer in your home, the burning smell may be due to the belt slipping on to the pulley. For those who have a pump that is driven by its own motor, the burning smell may be due to faulty motor. Before replacing the pump motor, make sure you assess the condition of the inlet, as dust particles can restrict the movement of the impeller. Pulley Assembly Some washers use the assembly to provide tension on the pump or drive belt. When the idler pulley or arm malfunctions, the tension of the belt is not maintained which causes excess friction and slippage. This will cause the belt to overheat and can create a burning smell. If you suspect that pump or drive belt is burnt, you must assess the condition of idler pulley and arm. If you notice rust or signs of wear and tear on the assembly, replace it immediately. Motor Coupling Some top loading washers use motor coupling instead of a belt to transfer electric power to the transmission from the motor. The coupling connects the drive motor to the transmission. It usually consists of two drive forks made of plastic and a rubber coupling. One fork is attached to the motor shaft and the other connects to the transmission shaft. When the shaft of the machine rotates, the coupling absorbs the pressure and prevents the fork from breaking. If you use the machine regularly, the coupling may wear out and cause the drive flock slip. This can be one of the causes of burning smell. To assess the condition of the coupling and to replace it, you must first get access to it. To do this, you should remove the washer cabinet. Make sure there is no power supply to the machine when you attempt repairs. Clutch Assembly Some washers use the clutch assembly to rotate the washtub. When your clutch is worn out, you can experience burning smell during the wash cycle. You could also hear a scraping sound during the spin cycle when the clutch is worn out. Another symptom of the clutch worn out is the brake shavings or dust found underneath the machine. If your washer displays these symptoms, you must replace the clutch. To replace the clutch, remove the cabinet and the motor assembly. Replacing the clutch assembly is not easy. To do this, it is best to get help from a washing machine technician. Spring and Glide Some washers use a glide and spring arrangement on the motor for belt tensioning. Normally, the motor is mounted on a solid frame and it uses spring to provide tension. A nylon glide or plastic fixed to the bottom of the motor to allow it to slide on the frame. This allows the pump or drive belt to slip a little when you start the machine and it acts like a clutch. When the glide does not slide properly, the belt gets overheated and may create a burning smell. If you experience burning smell when the motor starts, check the motor pivots, springs, and make sure the base is free of rust or dirt. If you suspect the glides to be defective, you must lubricate or replace them. Also, you may have to replace the belt if it is damaged or burnt. Here Are Our Service Areas In These Popular Cities: SummervilleMinneapolis, Billings, New Haven, Bowie, Milwaukee, Charleston SC, San Antonio, Orlando, Miami, Tampa, Richmond, Denver, Las Vegas, St. Louis, Columbia, Albuquerque, Henderson, Charlotte, Indianapolis, Tucson, San Jose, Jackson, Middletown, Chicago, Nashville, Portland, New York City, Aurora, Colorado Springs, Reno City, Olympia, Houston, Newark, Baton Rouge, Lakewood, Omaha, Providence, Virginia Beach, Jacksonville FL, Little Rock, Birmingham, Eugene, Tallahassee, Manchester, Raleigh, Allentown, San Diego, Salt Lake City, Portland, Cleveland, Austin, Everett, Fort Worth, San Francisco, Silver Spring, Detroit, Seattle, Pittsburgh, Philadelphia, Phoenix, Kansas City, Columbus, Oklahoma City, Dallas, Los Angeles, Atlanta, Tacoma, Baltimore, Boston, Provo, Sacramento, Louisville The post How to Fix A Washer With A Burning Smell appeared first on OnSite Appliance Drying your wet clothes during winters and rainy season can be difficult if you don’t have a dryer in your home. The dryer is an extremely useful appliance. But like any other residential appliance even the dryer could malfunction, which can disrupt your daily routine. In such situations, it is best to get appliance repair help from a professional dryer service technician. Using the services of a dryer repairman will ensure that repairs are carried out properly. Some people avoid using the services of a dryer service technician to reduce expenses. If you are one of those who plan to repair the machine yourself, you must identify the part responsible for the problem. Once you identify the part, all you have to do is replace it with a genuine part. Having a dryer that does not tumble can be a frustrating experience. To troubleshoot this problem, you must identify the part that can prevent the household appliance from tumbling. Here is a quick dryer repair guide to help you identify the problem part. Belt The belt connects the motor to the drum. When the belt rotates, it turns the drum. Regular use of the dryer can wear out the belt. If the dryer is not tumbling, you should check the condition of this belt. Belts that are broken or worn out must be replaced immediately. Ideally, the belt must have grips on both sides and should be flexible. Before changing the worn out belt of your machine, make sure you disconnect the power supply. To replace the belt, you must remove the front panel of the machine. Pulley Assembly When you load your clothes in the drum, the belt could slip on the drum or drive pulley. This could damage the drum and other parts of the machine. To prevent this, the idler pulley assembly is to provide tension on the belt. The pulley rotates at very high speeds and over time, it may get damaged due to increased friction. If you hear squealing or squeaking when the drum rotates, it indicates that idler pulley is damaged. If steps are not taken to troubleshoot the problem, the noise will increase and damage other parts of the machine. Another symptom of a problem with the pulley assembly is the reduced speed of the drum. If the drum of your house appliance does not move or moves very slowly, then you should check the condition of the pulley assembly. To check the condition of the assembly, you must remove the belt. If the pulley turns freely, it means that some other part is responsible for the problem with your machine. Also, visually inspect the condition of the shaft and replace it if it is worn out. The spring tension is responsible for holding the belt tightly. If it is unable to do so, you must replace the spring or the assembly. The shaft and the pulley assembly are usually located near the drive motor. To service these parts, you have to remove both the lower and front panel of your residential appliance. Maintenance Kit When you buy a new dryer, make sure you ask the dealer for the maintenance kit that comes with the machine. This kit will contain spare parts that are normally responsible for preventing the dryer from tumbling. Some of the parts that you can find in the kit are bearings, idler pulley, drum rollers, and belts. Once you find the part that is responsible for the problem, just replace it with the one available in the maintenance kit. This will make dryer repair even more economical. Drive Motor Both electric and gas dryers use a motor to turn the drum and the blower. When there is a problem with the motor, it will prevent the drum from rotating. It could even produce a humming sound when you use the machine. To service the motor, you have to remove the dryer’s front panel. Before checking the condition of the motor, make sure you check the power supply to the motor. Since this is a live voltage test, it must be performed by a qualified appliance service technician. Door Switch The door of most dryers is equipped with a switch that starts tumbling cycle when you close the door. If you don’t hear tumbling sound when the door closes, the door switch could be the culprit. The switch is usually attached to the machine’s front panel. If you suspect that the switch is responsible for the problem, you can check its continuity using a multi-meter. This test must be performed after you disconnect the power supply to the machine.
Other Service Locations In Popular Cities: Austin, New Haven, Milwaukee, Charleston SC, Tucson, San Antonio, Orlando, Miami, Las Vegas, Columbia, Henderson, Charlotte, Indianapolis, San Jose, Richmond, Jackson, Chicago, Nashville, Portland, Aurora, Reno City, Olympia, Houston, Lakewood, Providence, Eugene, Tallahassee, Manchester, Raleigh, Allentown, San Diego, Salt Lake City, Cleveland, Everett, Fort Worth, San Francisco, Silver Spring, Detroit, Seattle, Pittsburgh, Philadelphia, Phoenix, Kansas City, Columbus, Oklahoma City, Dallas, Los Angeles, Atlanta, Tacoma, Baltimore, Boston, Provo, Sacramento, Louisville, Baton Rouge, St. Louis, Portland, Jacksonville FL, Austin, Colorado Springs, Albuquerque, Virginia Beach, New York City, Middletown, Billings, Tampa, Denver, Little Rock, Birmingham, Newark, Omaha, Bowie, Minneapolis The post How To Fix A Dryer That Won’t Tumble appeared first on OnSite Appliance |
About UsOnSite appliance repair technicians specialize in fixing all major home appliances, so you can have peace of mind that any appliance repairman we send to your home in will not only be experienced but certified to work on your residential appliance. ArchivesNo Archives Categories |